Saturday, June 27, 2020

10HP Baguley: Steps 2 and 3

Okay, so I know I said I'd do a post per step in the instructions, but firstly step 3 is very short, and secondly it appears I didn't take any photos of the finished step 2 so they are a bit muddled together. So without further ado here are the instructions for step 2:

Attach inner cab back to footplate with the half etch detail facing inwards, followed by outer cab back with the upper beading facing outwards, followed by the other buffer beam. Add 2 lengths of 0.5 brass angle @ 14mm to the half etch recesses, bend the upper cab beading to form part of the grab rails to 90°
Quite a bit more to do in this step than step 1, with quite a bit of laminating parts together to form the rear cab wall. The rear of the chassis has three small tabs which go into slots on the inner cab wall and while the parts fitted together perfectly I wasn't sure how best to hold them so they were at right angles (so the wall ends up vertical) while I soldered them together. In the end I settled on using a present I received last Christmas.


Yes, I was given a set of 1-2-3 blocks for Christmas and this was the first time I'd used them. Their weight meant they didn't move and nicely held the wall part in place, while I could also use them to ensure the two parts were at right angles to one another. Okay, so being metal they acted as a heat sink meaning I needed longer with the iron to make joint, but it worked perfectly, and no burnt fingers!

With the inner wall in place I then laminated on the outer wall and buffer beam, again using a coupling hook to help with the alignment. With the rear wall built up I thought it wise to check that the chassis still fitted before going any further.


It was more difficult to fit than before, so I've eased the half round holes I filed a little further, but other than that there were no issues at all. Now while I'm yet to finish step 2 of the instructions here is what step 3 says.

Form the buffer beam irons to shape, using the profile jig in the etch. Trim the excess material to length, in line with the half etch notches, fit these formed irons to both front and rear buffer beams, using the alignment marks.
After the hassle of trying to solder the brass angle to the chassis to form the valences I opted to superglue them in place this time. I also superglued the buffer beam irons as I didn't want to risk disturbing the buffer beam overlays.


The buffer beam irons were quite awkward to fit as I'd only just left enough room behind the Greenwich couplings. In retrospect if I was building the kit again I'd do things a little differently. I'd probably fill in the slot in the buffer beam, and then either solder a small upright section to the middle of the buffer beam iron, or maybe make a single piece version from brass sheet. In fact if I had any of my experimental etched couplings they might be a good starting point. I should point out this isn't a criticism of the kit, as the current version allows you to easily produce a prototypicalyl accurate model while having a slot for the couplings. It's just that the nice buffer beam irons get lost behind the coupling which seems a shame. I'm now in two minds as to whether or not to alter the model to remove the Greenwich couplings, any thoughts would be greatly appreciated.

3 comments:

  1. I will sketch you a really useful tool for holding stuff whilst welding or soldering. It's a weighted hook with a horizontal bar on the plain end. You rest it on your 1-2-3 block and the hook hold stuff in place. Not that I would advocate welding on precision ground blocks. Also try preheating the parts, use the domestic oven, don't use multicore use solid solder and Bakers fluid. I enjoy watching, have fun.
    PS.Bakers may not be available as it does make one cough and splutter a bit, the upside is it clears the sinuses.

    ReplyDelete
    Replies
    1. PS. I have never used soft solder for anything but wires but even then I pre-tin the joints. A little gas air torch is well worth the investment.

      Delete
  2. If it was mine, I'd use the supplied 'bumper' with a tag soldered behind for a hook, even if that means raising it up on the buffer beam. That would give a nice simple 'beam with a coupling that tries to follow the prototype. And I might be tempted to epoxy it in place towards the end of the build.

    ReplyDelete